PIC18F6525T-I/PT【PDF 15/396 页】IC PIC MCU FLASH 24KX16 64TQFP

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录3881

11页 12页 13页 14页 [15页]16页 17页 18页 19页

2005 Microchip Technology Inc.

DS39612B-page 109

PIC18F6525/6621/8525/8621

10.3

PORTC, TRISC and LATC

Registers

PORTC is an 8-bit wide, bidirectional port. The corre-

sponding data direction register is TRISC. Setting a

TRISC bit (= 1) will make the corresponding PORTC

pin an input (i.e., put the corresponding output driver in

a high-impedance mode). Clearing a TRISC bit (= 0)

will make the corresponding PORTC pin an output (i.e.,

put the contents of the output latch on the selected pin).

The Data Latch register (LATC) is also memory

mapped. Read-modify-write operations on the LATC

PORTC.

PORTC is multiplexed with several peripheral functions

(Table 10-5). PORTC pins have Schmitt Trigger input

buffers.

When enabling peripheral functions, care should be

taken in defining TRIS bits for each PORTC pin. Some

peripherals override the TRIS bit to make a pin an

output, while other peripherals override the TRIS bit to

make a pin an input. The user should refer to the

corresponding peripheral section for the correct TRIS

bit settings.

The pin override value is not loaded into the TRIS

RC1 is normally configured by configuration bit,

CCP2MX, as the default peripheral pin of the ECCP2

module (default/erased state, CCP2MX = 1).

EXAMPLE 10-3:

INITIALIZING PORTC

FIGURE 10-8:

PORTC BLOCK DIAGRAM (PERIPHERAL OUTPUT OVERRIDE)

Note:

On a Power-on Reset, these pins are

configured as digital inputs.

CLRF

PORTC

; Initialize PORTC by

; clearing output

; data latches

CLRF

LATC

; Alternate method

; to clear output

; data latches

MOVLW

0xCF

; Value used to

; initialize data

; direction

MOVWF

TRISC

; Set RC<3:0> as inputs

; RC<5:4> as outputs

; RC<7:6> as inputs

PORTC/Peripheral Out Select

Data Bus

WR LATC

WR TRISC

Data

Latch

TRIS Latch

RD TRISC

Peripheral Data Out

VDD

VSS

RD PORTC

Peripheral Data In

I/O pin(1)

WR PORTC

RD LATC

Schmitt

Trigger

Note 1:

I/O pins have diode protection to VDD and VSS.

Peripheral output enable is only active if peripheral select is active.

TRIS

Override

Peripheral Output

Logic

TRIS OVERRIDE

Pin

Override

Peripheral

RC0

Yes

Timer1 Oscillator

for Timer1/Timer3

RC1

Yes

Timer1 OSC for

Timer1/Timer3,

ECCP2 I/O

RC2

Yes

ECCP1 I/O

RC3

Yes

SPI/I2C

Master Clock

RC4

Yes

I2C Data Out

RC5

Yes

SPI Data Out

RC6

Yes

USART1 Async

Xmit, Sync Clock

RC7

Yes

USART1 Sync

Data Out

Enable(2)

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式